International Standard
ISO 20816-2:2017
Mechanical vibration — Measurement and evaluation of machine vibration — Part 2: Land-based gas turbines, steam turbines and generators in excess of 40 MW, with fluid-film bearings and rated speeds of 1 500 r/min, 1 800 r/min, 3 000 r/min and 3 600 r/min
Reference number
ISO 20816-2:2017
Edición 1
2017-07
International Standard
Vista previa
ISO 20816-2:2017
70047
No disponible en español
Publicado (Edición 1, 2017)
Esta norma se revisó y confirmó por última vez en 2023. Por lo tanto, esta versión es la actual.
Esta norma tiene 1 modificaciones.

ISO 20816-2:2017

ISO 20816-2:2017
70047
Idioma
Formato
CHF 129
Convertir Franco suizo (CHF) a tu moneda

Resumen

ISO 20816-2:2017 is applicable to land-based gas turbines, steam turbines and generators (whether coupled with gas and/or steam turbines) with power outputs greater than 40 MW, fluid-film bearings and rated speeds of 1 500 r/min, 1 800 r/min, 3 000 r/min or 3 600 r/min. The criteria provided in ISO 20816-2:2017 can be applied to the vibration of the gas turbine, steam turbine and generator (including synchronizing clutches). ISO 20816-2:2017 establishes provisions for evaluating the severity of the following in-situ, broad-band vibration:

a) structural vibration at all main bearing housings or pedestals measured radial (i.e. transverse) to the shaft axis;

b) structural vibration at thrust bearing housings measured in the axial direction;

c) vibration of rotating shafts radial (i.e. transverse) to the shaft axis at, or close to, the main bearings.

These are in terms of the following:

- vibration under normal steady-state operating conditions;

- vibration during other (non-steady-state) conditions when transient changes are taking place, including run up or run down, initial loading and load changes;

- changes in vibration which can occur during normal steady-state operation.

ISO 20816-2:2017 is not applicable to the following:

i) electromagnetic excited vibration with twice line frequency at the generator stator windings, core and housing;

ii) aero-derivative gas turbines (including gas turbines with dynamic properties similar to those of aero-derivatives);

NOTE ISO 3977‑3 defines aero-derivatives as aircraft propulsion gas generators adapted to drive mechanical, electrical or marine propulsion equipment. Large differences exist between heavy-duty and aero-derivative gas turbines, for example, in casing flexibility, bearing design, rotor-to-stator mass ratio and mounting structure. Different criteria, therefore, apply for these two turbine types.

iii) steam turbines and/or generators with outputs less than or equal to 40 MW or with rated speeds other than 1 500 r/min, 1 800 r/min, 3 000 r/min or 3 600 r/min (although generators seldom fall into this latter category) (see ISO 20816-3);

iv) gas turbines with outputs less than or equal to 40 MW or with rated speeds other than 1 500 r/min, 1 800 r/min, 3 000 r/min or 3 600 r/min (see ISO 20816-3 or ISO 20816-4);

v) the evaluation of combustion vibration but does not preclude monitoring of combustion vibration.

Informaciones generales

  •  : Publicado
     : 2017-07
    : Norma Internacional confirmada [90.93]
  •  : 1
     : 23
  • ISO/TC 108/SC 2
  • RSS actualizaciones

 Modificaciones

Las enmiendas se emiten cuando se decide que puede ser necesario agregar nuevo material a un documento de normalización existente. También pueden incluir correcciones editoriales o técnicas que deban aplicarse al documento existente.

Amendment 1

Edición 2024

ISO 20816-2:2017/Amd 1:2024
87294
Idioma
Formato
CHF 18
Convertir Franco suizo (CHF) a tu moneda

Got a question?

Check out our FAQs

Customer care
+41 22 749 08 88

Opening hours:
Monday to Friday - 09:00-12:00, 14:00-17:00 (UTC+1)